Twister T2 Wet & Dry Bud Trimming Machine

The Twister T2 Wet & Dry Bud Trimming Machine is built for commercial cultivation facilities that have moved beyond simply asking how quickly they can trim and now need to control the entire processing workflow around throughput, consistency, sanitation, worker safety, and future expansion.

Capable of processing up to 35 lbs of wet material or 11 lbs of dry material per hour with a single machine, the T2 is designed for continuous production environments where manual trimming has become a serious labor bottleneck. Instead of depending on a large seasonal trimming crew, operators can establish a repeatable process that continues running batch after batch with consistent mechanical settings.

• Throughput: Up to 35 lbs Wet or 11 lbs Dry Per Hour
• Precision: 19,250 StaySharp Cuts Every Minute
• Sanitation: Full High Pressure Washdown Ready Design
• Scalability: Expand to 124 lbs Per Hour Inline

The T2 is powered by an industrial cutting system built around 11 StaySharp blades producing approximately 19,250 cuts every minute. Rather than simply increasing tumbler speed to chase throughput, Twister engineered the system around extremely rapid, precise cutting action combined with controlled movement through the tumbler. When two machines are used together, Twister states that the combined 22 StaySharp blades deliver almost 40,000 precise, scissor like cuts every 60 seconds.

That cutting performance is paired with a 304 stainless steel tumbler, nitrided steel blades, commercial motors, full guarding, interlocked safety systems, and washdown ready electrical components. Twister designed the modern T2 specifically around the demands of regulated commercial processing environments, with an emphasis on both production performance and the ability to repeatedly clean the machine between shifts and batches.

For facilities processing larger harvests, the T2 also provides one of the most important characteristics a capital equipment purchase can offer: you do not have to replace it when your production increases.

Start with one T2. Add a second when volume grows. Add a third when the facility requires another jump in capacity. Twister's continuous flow architecture allows multiple machines to operate inline, with published wet throughput reaching 78 lbs per hour with two machines and 124 lbs per hour with three machines.

That makes the T2 less like an isolated trimming machine and more like the foundation of a scalable commercial harvest line.

Commercial Throughput Without Sacrificing Control

The T2 is designed for operations where several hundred pounds of material can turn trimming into one of the largest labor demands in the entire harvest process.

A single T2 processes up to 35 lbs per hour wet or 11 lbs per hour dry.

Unlike a traditional batch trimming machine, the T2 operates as a continuous flow system. Material enters one side, progresses through the rotating tumbler, passes through the primary cutting zone, and exits the opposite end.

That continuous movement allows operators to establish a predictable production rhythm rather than repeatedly loading, stopping, unloading, and restarting individual batches.

Twister specifically promotes the T2 for continuous duty operation in demanding harvest environments.

For a commercial facility, the value of that design goes beyond simple pounds per hour. Preparation staff can continuously supply the trimming line. Quality control staff can continuously inspect finished material. Conveyors can continuously feed and discharge the system. Trim collection can operate simultaneously.

The T2 therefore becomes part of a production line rather than a standalone machine that dictates the rhythm of the entire room.

19,250 Precision Cuts Per Minute

The cutting system is one of the defining differences between the T2 and lighter duty trimming equipment.

The T2 uses 11 StaySharp cutting blades engineered to perform approximately 19,250 cuts per minute.

With two T2 units operating together, Twister states that 22 StaySharp blades deliver almost 40,000 precise cuts every minute while maintaining uniform output hour after hour.

The objective is not simply raw cutting speed. The rapid blade action allows unwanted leaf material that passes through the tumbler openings to be cut quickly while the flower itself continues moving through the drum.

That relationship between tumbler movement and blade speed is central to producing commercial throughput while minimizing unnecessary time inside the trimming chamber.

Wet Trimming Preparation

For wet trimming, Twister recommends processing flower soon after it has been removed from the plant.

The manufacturer recommends watering plants approximately four to six hours before trimming and keeping them cool before processing. The reason is mechanical: firm leaves are easier for an automated cutting system to engage, while wilted leaves can wrap around the flower and reduce performance.

Preparation matters just as much. Twister recommends removing larger fan leaves and excessive leafy material before the flower enters the T2. Stems should also be cut close to the flower. Large pieces can wrap around the product and reduce the opportunity for unwanted material to reach the cutting blades.

That preparation helps the machine spend its processing time performing precision cleanup instead of trying to remove large material that should have been eliminated upstream.

Dry Trimming at the Correct Moisture Level

Dry trimming introduces a completely different material condition.

Twister recommends approximately 10% to 11% moisture for dry processing. At this point, the outside of the flower should feel dry while the interior retains some resilience.

The manufacturer provides a simple physical test: if the flower crumbles when lightly squeezed, it is too dry; if it remains compressed, it is too moist; if it compresses and then rebounds, it is closer to the desired condition.

This matters because over dried material can become more fragile during mechanical handling, while material that remains too moist may not allow unwanted leaf to separate efficiently.

Different Tumblers for Different Conditions

Twister's own trimming documentation demonstrates how seriously it treats product condition.

For dry processing, the company's historical guide identifies a 3/16 inch stainless steel tumbler as an effective configuration for most dry flower types. A quarter inch tumbler may perform differently with larger flower and moisture levels around 11% to 13%.

For wet processing, the standard guide identifies a quarter inch stainless steel tumbler, while the smaller 3/16 inch option may improve results with certain smaller flower types.

The key point is not that one configuration is universally superior. The T2 platform allows operators to select the setup that best matches their product and quality goals.

Dial In the First 10 to 15 Minutes

Twister specifically recommends using the beginning of each trimming session to evaluate the incoming product and establish the appropriate processing rhythm.

Three variables should be considered: machine incline, loading speed, and time inside the tumbler.

As a starting reference, Twister recommends beginning with the machine level, loading approximately one handful every 20 to 30 seconds, and targeting approximately 30 to 45 seconds inside the tumbler.

These are not fixed rules. They are a baseline from which operators can adjust the machine around the actual flower being processed.

Residence Time Controls Final Quality

The T2 should not simply be fed as fast as physically possible.

Material needs enough time inside the cutting zone for unwanted leaf to interact with the trimming system.

Twister recommends loading an initial quantity of roughly two ounces, allowing it approximately 30 to 45 seconds in the tumbler, and then gradually introducing additional handfuls every 20 to 30 seconds.

Once the system reaches equilibrium, new material entering the machine pushes processed material toward the discharge side.

That establishes the continuous flow rhythm the T2 was designed around.

Avoid Overloading the Tumbler

One of the easiest ways to reduce trimming quality is to overload the T2 in an attempt to increase throughput.

Twister recommends keeping approximately two ounces of material in the tumbler during normal operation and describes approximately half full across the width of the tumbler as an effective working amount.

Excessive material prevents flower from moving properly and limits the ability of the leaf to reach the cutting surface.

In other words, commercial output comes from continuous flow, not from packing the machine as full as possible.

Quality Control Happens While You Trim

The T2 is designed to be adjusted during production.

As the first material exits, operators should evaluate the final appearance.

If additional trimming is required, Twister recommends either reducing the incline or slowing the loading rate so the material spends more time inside the tumbler.

Once the desired result has been established, operators can maintain a repeatable loading rhythm.

This approach lets facilities build processing recipes around different cultivars and material conditions rather than rediscovering the correct process every harvest.

Scale From 35 to 124 lbs Per Hour

One of the strongest reasons to invest in the T2 is its ability to grow with the facility.

Twister's continuous flow architecture allows multiple T2 units to run inline.

Published throughput for the current commercial system is: one T2 up to 35 lbs per hour wet, two T2s up to 78 lbs per hour wet, three T2s up to 124 lbs per hour wet. For dry trimming, one T2 processes up to 11 lbs per hour and two T2s reach up to 25 lbs per hour.

Twister's brochure also explains that two T2 units can operate back to back without requiring additional operators.

That creates a very different investment path from equipment that must be replaced once production exceeds its original capacity.

Add Equipment as Your Facility Grows

The T2 can be expanded into a complete processing line with Twister rails and conveyor systems.

Available infrastructure includes the T2 Rail, Rail Extensions, Inbound Feed Conveyor, Outbound Quality Control Conveyor, T2 Leaf Collector, and T2 Trim Saver. Twister lists each of these as compatible T2 accessories and system components.

The inbound conveyor improves feeding consistency while the outbound conveyor provides operators with an organized quality control station where material can be visually inspected and touched up before moving downstream.

Twister states that its feed conveyor can improve trimming speed and consistency by up to 20%.

Portable Despite Its Industrial Build

The T2 is a serious commercial machine, but it is not permanently anchored to one processing line.

Heavy duty wheels allow the machine to be moved between processing areas or repositioned for cleaning and maintenance. Twister specifically highlights the wheeled chassis as useful for both indoor and outdoor movement.

That mobility can make a major difference in facilities where harvest rooms need to be reconfigured throughout the year.

Optional Leaf Collector

The T2 can be configured with Twister's commercial Leaf Collector for integrated trim removal.

The collector uses a 2 HP motor, provides approximately 1,700 CFM of airflow, and operates from a 230V supply.

For facilities using the standard collection workflow, the Leaf Collector provides the suction required to continuously remove cut material from the trimming chamber and direct it into the collection system.

Optional Trim Saver

Facilities that consider recovered trim a valuable secondary product can upgrade to the Twister T2 Trim Saver.

Twister's own trimming guides describe the Trim Saver as the premium option when recovered material needs to remain intact for extraction, pressing, and related processing.

Instead of forcing the collected material through a conventional vacuum impeller, the Trim Saver uses radial cyclone technology to generate airflow while effectively bypassing the impeller.

That allows the trimming line to protect value on both sides of the tumbler.

Strength in Numbers

Recommended Wet Processing Practices

• Process freshly bucked material soon after removal from the plant.
• Keep plants cool before trimming.
• Water approximately four to six hours before the session.
• Remove larger fan leaves before loading.
• Cut stems close to the flower.
• Begin with approximately two ounces of material.
• Allow approximately 30 to 45 seconds before adding more.
• Continue feeding approximately one handful every 20 to 30 seconds once the process is dialed in.

Recommended Dry Processing Practices

• Target approximately 10% to 11% moisture.
• Remove fan leaves and larger leafy material before drying.
• Cut stems close to the flower before processing.
• Begin with the T2 level.
• Start with approximately two ounces of material.
• Target approximately 30 to 45 seconds inside the tumbler.
• Adjust machine incline or loading speed based on final appearance.

Cleaning and Maintenance

Routine Cleaning

Twister recommends cleaning the T2 approximately every four hours of operation and the Leaf Collector approximately every eight hours. Approved cleaning options include Simple Green Industrial Cleaner and 99% rubbing alcohol.

T2 Cleaning

• Disconnect the machine from power.
• Remove the tumbler, hopper, and protective shrouds.
• Apply the appropriate cleaning solution.
• Pressure wash the machine or clean it by hand.
• Clean the tumbler separately.
• Run the machine briefly after washing to remove excess water.
• Finish drying with compressed air.

Leaf Collector Cleaning

• Remove and clean the filter bag.
• Disconnect the hose and open the housing.
• Remove the impeller for hand cleaning.
• Clean the inside of the housing.

Operator Safety

The T2 is a high speed cutting machine and should only be operated by trained personnel.

• Always use a properly grounded electrical receptacle.
• Do not overload electrical outlets or extension cords.
• Disconnect the machine before removing protective covers.
• Keep all guards installed before connecting power.
• Turn the machine off and unplug it before cleaning.
• Keep hands and body parts away from moving equipment.
• Avoid loose clothing and jewelry, and confine long hair.
• Wear safety glasses at all times during operation.

What's Included

• Twister T2 Commercial Trimmer
• Standard Stainless Steel Tumbler
• Product Hopper for Standalone Machine Configuration
• Integrated Safety Guarding
• Mobile Wheeled Frame
• Owner's Manual and Operating Documentation

The Leaf Collector is available as an optional configuration and is not included when the Trimmer Only option is selected.